WHY LEARNING PLUMBING BASICS IS VITAL FOR BATHTUB INSTALLATION

Why Learning Plumbing Basics is Vital for Bathtub Installation

Why Learning Plumbing Basics is Vital for Bathtub Installation

Blog Article

Visit My Website

Do you find yourself trying to locate know-how concerning How to Install a Bathtub?


How to Install a Bathtub Yourself
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging job. If the old tub is readily accessible, the project can move speedily; if you need to open a wall surface to get rid of the old tub and place the brand-new bathtub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require a helper to move out the old bathtub and also embeded in the brand-new one. Make sure you have actually qualified yourself for the task and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed project, it is far better to consider using one prior to you begin. Possibilities are you may need a specialist plumber to make tube links.
This post will aid you mount a brand-new bathtub in your restroom if you have already purchased a brand-new tub and also do not require to alter the arrangement of your previous water supply pipelines.
Your tools as well as material list ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the restricted gain access to that is often the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipes. As soon as the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
    Before proceeding to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, after that you will need a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipelines.
    If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Protect the tap in place with the producer offered backnut. When the tap is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Mounting the Tub


    Making use of the two wooden boards under its feet, put the bathtub in the required setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
    The following goal is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub up until the level checks out level.
    To set up faucets, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
    Activate the water supply and check all joints and new pipework for leaks and also tighten them if essential. Load the bath tub as well as likewise check the overflow outlet and also the typical outlet for leaks.
    Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of a minimum of once as this will certainly resolve it right into its final setting.

    Getting ready for the Setup


    First of all, the supporting frame supplied with the bathroom ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the bathtub.
    Fit the versatile tap ports to the bottom of the two taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
    Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last position.

    Tiling Around the Tub


    In the location where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
    You can choose from a variety of coloured sealers to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to allow for the movement experienced when the bathtub is in usage. The sealant can fracture rather very early if you do not take into account this activity before securing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the market. It is advisable to fit the tiles making use of waterproof or waterproof adhesive as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I'm very intrigued by How to Install a Bathtub Yourself and I hope you liked the new page. If you liked our article please don't forget to pass it around. Thanks a lot for your time spent reading it.


    Hot water gone? Dial here.

    Report this page